ELUXI_CW_Free_Space_Circular_Diode_Lasers

The MatchBox Series

The MatchBox Series is a powerful platform, encompassing CW lasers, 4-wavelength diode combiners and Q-Switch nanosecond lasers. It offers simplicity of integration and selection of >150 products within the series.

Control Interface

MatchBox series lasers (2nd edition) feature a Universal Asynchronous Receiver/Transmitter (UART) controller interface. The pinout is explained below - separately for diode and DPSS lasers. A 'breakout box' is used for converting UART into USB or RS232 protocols. The converter chip for USB is 'Silicon Labs CP2102' and for the RS232 it is 'MAX232'.

Software Interface

Laser control softwareThe MatchBox laser control software is used for checking preset parameters, such as the max. laser diode current, target temperatures for TEC1 and TEC2 and actual measured values of these parameters, as well as the load percentage of the Peltier elements. This is very helpful for laser diode age tracking and other troubleshooting actions. Also the software indicates if the laser is working in ACC (Automatic Current Control) or APC (Automatic Power Control) mode.

Specifications

BEAM PROPERTIES:

Transversal mode: TEM00, except 500 mW versions of 532 nm and 785 nm
Beam diameter at aperture (1/e2): <2 mm for diode and ~1 mm for DPSS
Beam divergence (full angle): <2 mrad for diode and <1.5 mrad for DPSS, except 500 mW versions of 532 nm and 785 nm
Beam pointing stability: <1 mrad/C°
Bore sight error: +/-2 mrad (vertical), +/-3 mrad (horizontal)
Beam quality, M2: 1.1 to 1.5, except multimode 500 mW versions of 532 nm and 785 nm
Polarization ratio: better than 500:1 for DPSS and better than 1000:1 for diode lasers.

POWER STABILITY:

Power stability of free-space lasers is <1 % RMS over 8 hrs
Power stability of fiber-coupled lasers is <2 % RMS over 8 hrs
Non-SLM DPSS lasers have significant noise peaks at above 200 kHz

MODULATION:

Fast TTL modulation of non-SLM diode lasers is implemented on request
For SLM diode and all DPSS lasers, the TTL pin is configured for fan speed control
Modulation of DPSS lasers (up to few kHz) is implemented upon request

FIBER SPECS:

SLM fiber coupled lasers are made with FC/APC connectors
Non-SLM lasers are made with FC/PC connectors Standard length of a fiber is 1 m to 1.2 m
Polarization extinction ratio (PM fiber): better than 20 dB
Polarization rotation (PM fiber): less than 5 degree

PHYSICAL PROPERTIES:

Control interface type: UART serial bus, convertible to USB with standard accessories
External power supply requirement: +5VDC, 5A for DPSS, 1.5 A for diode up to 200 mW
Dimensions (L-W-H): 50 x 30 x 16 mm (excluding pins and output window)
Beam height from the base: 10.4 mm (+/- 0.3 mm)
Heatsink requirement: diode <1 °C/W, DPSS <0.5 °C/W
Optimum heatsink temperature (non-condensing): +15…+30 °C
Max. heatsink temperature 40 °C Internal temperature stabilization: TEC
Overheat protection: Yes
torage temperature (non-condensing): -10 to +50 °C
Warranty: 12 months
Hours limitation of 5000 hrs applies for 405, 445, 488, 515, 633, 635, 660 nm diode lasers. Operational time calculation is based on an internal EPROM counter

COMPATIBILITY:

RoHS
General Product Safety Directive (GPSD) 2001/95/EC
Electromagnetic Compatibility (EMC) Directive 2004/108/EC

IEC60825-1:2014 (compliant only using additional accessories)